Int 7C/AX=0007h

lup.gif ldown.gif Interrups Categories Contents

rbline.gif

SK-UPPS Data Link Interface API - REGISTER PROTOCOL

AX = 0007h
ES:BX -> Protocol Control Block (see #03849)

Return:
AX = completion code (see #03846)

Program: SK-UPPS is the Schneider & Koch Universal Portable Protocol Stack, which provides an API on top of its Data Link Interface, allowing the use of any of several network transport layers

See Also: AX=0008h - AX=000Bh

Format of SK-UPPS Protocol Control Block (PCB): Offset Size Description (Table 03849) 00h WORD (big-endian) protocol type 02h WORD protocol mode (see #03850) 04h DWORD -> Receive Upcall routine (see #03851) 08h DWORD -> Transmit Upcall routine 0Ch DWORD -> Event Upcall routine (see #03853) 10h DWORD -> ASCIZ protocol name (zero if none) 14h WORD protocol ID will be returned here (always non-zero)

Bitfields for SK-UPPS protocol mode: Bit(s) Description (Table 03850) 0 promiscuous mode; protocol receives all frames regardless of their destination (PROTOCOL TYPE must be FFFFh) 1 if set, protocol's Event Upcall will be called on entry and exit of the DLI's Interrupt Service Routine (see #03854) 2 DLI 2.2+ hook mode; protocol receives all directed frames destined for this station (PROTOCOL TYPE must be FFFFh) 3 DLI 2.3+ receive error frames (only valid in promiscuous mode (0)) 4-5 DLI 2.5+ frame type:. 00 Ethernet II; specify type code in PROTOCOL TYPE field (high-low). 01 IEEE 802.2; specify Service Access Point (SAP) in MSB (offset 0) of PROCOTOL TYPE field; LSB must be zero. 10 IEEE 802.2 with SNAP header; specify type code in PROTOCOL TYPE field (high-low). 11 reserved (currently unused) 6 DLI 2.5+ if set, protocol's Event Upcall will be called with event code EV_BUFFER_WANTED, when DLI runs out of Mbufs 7 DLI 2.7+ chain mode; if set, client allows the specified frame type to be shared with other clients 8 DLI 2.8+ receive non-LLC frames rather than LLC frames 9 DLI 2.8+ receive all multicast frames (see also AX=0009h) 10-15 reserved (currently unused; must be zero)

Notes: If PROTOCOL TYPE is FFFFh and neither the "promiscuous" nor the "hook" mode is set, the protocol receives all frames that did not match any registered frame type (demultiplexor mode).. Protocols using "promiscuous", "hook" or "chain" mode should always return from the Receive Upcall with the received Mbuf in ES:BX and the Carry Flag set. The DLI will then pass the Mbuf to the FEED BACK BUFFER function (see AX=000Fh).. Some DLIs do not support all or even any of the "promiscuous", "receive non-LLC" and "receive all multicasts" mode bits.

See Also: #03849

(Table 03851) Values SK-UPPS Receive Upcall is called with:. ES:BX -> Mbuf. AX = receive status (see #03852) (also stored in Mbuf's RECEIVE STATUS field). Interrupts disabled

Return:
Nothing

See Also: #03853

Bitfields for SK-UPPS receive status: Bit(s) Description (Table 03852) 0-2 reserved (0), currently unused 3 frame check sequence (FCS) error 4 overflow (frame too long) 5 framing error 6 reserved (0), currently unused 7 non-LLC frame (see #03850 [bit 8]) 8-15 reserved (0), currently unused

Notes: The protocol's Receive Upcall routine will be called whenever a frame matching the specified frame type is received. A received frame is passed to the protocol in the Mbuf's DATA area at OFFSET and its size is LENGTH bytes.. The receive status passed to the Receive Upcall in register AL is always zero, except for protocols using "non-LLC" mode (8 of PCB's protocol mode field) or "promiscuous" mode together with "receive error frames" (0 & 3).. Upcalls are FAR routines and must return with a RET FAR. If the Carry Flag is set on return from a Receive or Transmit Upcall, then ES:BX must point to an Mbuf, which the DLI will then pass to the RELEASE BUFFER function (see AX=0005h). See also notes for PROTOCOL MODE.

(Table 03853) Values SK-UPPS Event Upcall is called with:. AX = event code (see #03854)

Return:
Nothing

Note: All Event Upcalls may be ignored by the protocol.

See Also: #03851

(Table 03854) Values for SK-UPPS Event Upcall event code: 00h EV_BUFFER_AVAILABLE client may now call REQUEST BUFFER (AX=0004h) 01h EV_ISR_START start of Interrupt Service Routine 02h EV_ISR_END end of ISR (see #03850 [bit 1]) 03h EV_BUFFER_WANTED DLI temporarily out of Mbufs 04h EV_NETWORK_STATUS DLI 2.8+ network status -- DX=status (see #03855) 05h EV_IO_CONTROL DLI 2.8+ I/O control -- DX=subfunc (see AX=0016h)

See Also: #03853

Bitfields for EV_NETWORK_STATUS in register DX: Bit(s) Description (Table 03855). Token-Ring FDDI 15 SIGNAL_LOSS SIGNAL_LOSS 14 HARD_ERROR HARD_ERROR 13 SOFT_ERROR SOFT_ERROR 12 TRANSMIT_BEACON TRANSMIT_BEACON 11 LOBE_WIRE_FAULT PATH_TEST_FAILED 10 AUTO_REMOVAL SELF_TEST_REQUIRED 9 reserved reserved 8 REMOVE_RECEIVED REMOTE_DISCONNECT 7 COUNTER_OVERFLOW reserved 6 SINGLE_STATION DUPLICATE_ADDRESS 5 RING_RECOVERY NO_RING_OP_STATUS 4 reserved VERSION_MISMATCH 3 reserved STUCK_BYPASS 2 reserved FDDI_EVENT 1 reserved RING_OP_CHANGE 0 reserved reserved

Note: EV_NETWORK_STATUS is not supported on Ethernet

Category: Network - Int 7Ch - S

rbline.gif

lup.gif ldown.gif Interrups Categories Contents